Your cart is empty.
Your cart is empty.ReadyLift is the fastest, safest and least expensive way to lift, level, or raise the rear of today's most popular trucks and SUV's and add wheels and tires up to 37 inches in diameter. While other lift kits cost thousands to buy and hours to install, ReadyLift can be installed in as little as 1 hour, and can cost less than the price of a single custom wheel. ReadyLift recommends custom wheels no wider than 9.0 inches with 4.5 inches - 5.5 inches of backspacing on most applications. Using wheels wider than 9.0 inches may require a larger backspacing or a reduced tire height to minimize the chance of tire to fender clearance problems on some applications. ReadyLift states that it is the responsibility of the installer to verify correct and safe fitments. ReadyLift does not assume responsibility for any errors or misapplication contained within this guide.
BowWow
2025-08-02 18:25:03
Easy install, parts all fit well, U-bolts were long enough. Good product. My truck sat about 3/4" high in the front (installed 3" leveling springs), and I wanted just a little rake. I wavered between the 1" and 2" blocks, and finally pulled the trigger on the 2". After install I have just a little too much rake, so I'll be ordering the 1" blocks. I think that will give me a better level and look.
Troy Barry
2025-07-07 12:12:04
Easy install, works great. I raised my Ram 3500 2021, 2†in the rear and 3†in the front, measuring from the fenders, the front sits 1/2†lower now. It looks level and great. I would buy again.
Customer
2025-05-27 13:30:13
2010 Dodge 2500 Cummims with the AAM 11.5 axle.Installed easily.All black hardware is nice. Blends in when looking at the axle.Only 2 complaints for 4 stars...1) No torque spec provided, and it was nearly impossible to find one. I had to look at intrustructions online from a super lift kit. I ended up using 120 ft/lbs.2) casting for blocks not perfect, looks slightly off center on one block when torqued down. Very slight. When I took it to get aligned had the shop check it. They had seen that before and said it was common and wouldn't hurt it. You have to get in close to see it, but it still bugs me.Overall nice product though.
Christy H.
2025-05-24 10:04:41
Very quick and easy to install on my 2010 Dodge Ram 2500 mega cab. Truck has a 3“ leveling kit on the front.
DAVID G. EVANS
2025-05-17 12:16:09
Terrible! Does not fit a 2003 Dodge Ram 2500HD 5.9L Cummins. The blocks are not correct with the safety stud on top, it is to big to fit into leaf springs so I had to cut it off. Had to be installed after all the work done and I would give it 0 stars if I could.
Cody Cochran
2025-04-05 12:19:23
Blocks worked great. Had to have custom u bolts made as mine where square not round. Also stock ubolts are 3/4†while these are only 1/2â€. Kit worked well but had to do some thinking outside the box and got different ubolts. In companies defense picture is accurate.
Kingkong309
2025-03-31 18:44:05
Looks good with 3 in lift in front
Insight in Colorado
2025-03-25 17:56:07
It seemed to be a decent product. However, it was very strange that two of the 8 nuts were 21 mm, and six were 22 mm. Very inconvenient, and likely will involve some future owner stripping them. Also, the instructions fail to mention that you must orient the 1/8" taper with the narrow edge toward the front of the truck. And also fails to describe the torque sequence: Torque both nuts on inboard U-bolt to 55 ft lbs, then outer. Next, torque bolts to 92 ft-lbs, starting with the one showing fewest threads. Then torque all to 129 ft lbs, starting with one showing fewest threads. Decent potential, but poor execution by ReadyLift.
martin therrien
2025-01-12 13:48:47
Super bon kit facile installé merci
JustynK
2024-12-23 13:25:18
Worked well everything was as advertised
SR
2024-12-22 11:34:14
This kit worked on my 2021 Ram 3500 when paired with the Readylift airbag extenders AND new longer shocks (I went BDS NX2s made for a 2" lift). The stock shocks will fit, but they'll be at or near max extension, and might even pull the rear alignment off.
Doug Drolet
2024-12-06 14:22:40
Was a good kit had to machine spacer block to fit was not machined to fit my application
Anthony Fuoco
2024-11-19 20:43:41
The centering stud on the top of the block is about 5/8", but the hole in the leaf spring that it needs to mate into is 1/2". Total waste of money. Extremely frustrating to get the rusty u bolts off, only to find out you have to put it all back together.
Recommended Products
$170.00
$ 77 .99 $77.99