Your cart is empty.
Your cart is empty.Product Description
Contact adhesive on your furniture
High Quality : Wood strip is more durable and lasting
Perfect Size: The thickness is 0.6mm, It's suitable for your daily needs. Edge Banding is a strip of wood veneer with heat melt adhesive pre-applied to the back. You simply hold the edge banding in place, then run over it with a heated iron. After cooling, please press it with your hand and trim off the excess sides with the Utility Knife, 0.6mm thickness can let you easy to do.
-
Red Oak edge banding
EASY APPLICATION
Red Oak edge banding
-
Red Oak edge banding
First
You simply hold the edge banding in place,
run over it with a household iron to heat the
adhesive.
-
Red Oak edge banding
Second
Wait for the edge banding cooling 10 minutes
-
Red Oak edge banding
Third
Press it with your hand and trim off the excess with the
utility knife
-
Red Oak edge banding
Final
Finished
Red Oak Edge banding is a thin material used to seal the sides.
Laminate
Cabinet
Door
Desk
vibrata chromodoris
2025-08-12 18:38:50
Great match for my Ikea Billy bookcase with birch finish. Virtually seamless. Easy to apply.
E. Gibson
2025-08-10 13:48:09
The media could not be loaded.
Lisa
2025-08-08 13:16:28
This is the best stuff ever for making flooring in my dollhouse. It is easy to cut and apply. It looks more real and lifelike than other flooring I have seen.
Ms. SVM
2025-06-24 10:54:53
I used this product in size 1-1/2†for a small table project where I attached two - 3/4" plywood boards together to use as a tabletop and attached legs. I added this product to the edge of all 4 sides of the wood to hide the plywood layers. Worked surprisingly well and you can't tell that the tabletop is 2 pieces which really took the aesthetic up several notches! I used a hot iron and it adhered nicely. It was easy to cut, easy to sand lightly with my orbital sander, easy to shave the excess edging off for a perfect fit, and it took to my walnut stain very well - the color was even, not blotchy at all and matched the top very nicely. The only reason I gave it four stars instead of five is because at the very ends of the table where the corners meet, the edging was lifting a bit, no matter how many times I went over it with the iron. To rectify that, before I stained the piece, I just added a couple dots of gorilla wood glue to the edges and that worked perfectly in keeping the edges down. I enjoyed using it as it was quite easy (for my limited experience in wood working) and I really love the way it turned out. I would absolutely buy this again and I recommend this product.
James
2025-05-31 11:36:51
I was excited to find this wide edge banding. I ironed it on, and it seemed to adhere well. It was practically transparent--you could see the plywood edge underneath. I wasn't worried, as I was going to be painting it anyway. Unfortunately, as the paint did it's job, the banding bubbled up. This occurred all over the piece I was working on, taking it from looking like a very nice DIY job to amateur hour. :( Other edge banding from H.Depot was thicker and adhered better, without any issue.
Tribute
2025-04-03 14:29:11
Great match for Baltic Birch Plywood, easy to apply with a standard fabric iron on cotton setting, easy to sand.
Amanda EHess
2025-03-05 11:54:25
This product did not come with instructions. I was able to figure it out by looking up videos. I bought this product after a home improvement project. I needed some shelves for my bedroom closet but was unable to find any premade ones that would fit. I decided to build my own. I used 3/4 plywood. The shelves were great but the edges were unfinished and unattractive. I researched and found this product. I ordered it, it arrived quickly, and was excited to use it. I actually used a Cricut small iron to adhere the product. I recommend having a heat resistant glove or cloth of some sort before you start as well as a box cutter or a pair of scissors. I began by lining up the edges of the product and started ironing. It did get hot and started peeling away from the edge of the wood so I used a piece of cloth to press it back down. I held it for several seconds and kept going heating and holding. It got easier and faster the more I worked. When the adhesive heats up it makes the strip very tacky. Before heating the strip is somewhat ridged butane heated it becomes more flexible. 50 ft. for my small project was more than enough but I now have some for future projects!
C. Ellingson
2025-01-31 21:48:44
Used an iron for waxing skiis. Cleaned edges with a box razor. Worked perfect.
Craig E
2025-01-22 12:16:34
Easy to install with the glue already on the banding. Just heat it up and let it cool down
Recommended Products