• SDT103 Automotive Smoke Leak Detector can assist service technicians in leak detection testing. The SDT103 Automotive Smoke Leak Detector can assist service technicians in leak detection testing. Leak detection is the most basic but absolutely essential test in the automotive repair process. The SDT 103 Automotive Smoke Leak Detector is capable of outputting a constant standard test pressure of 32 mbar required by automotive EVAP systems through precise pressure regulation of the external air source, which can output smoke within seconds and can find leak holes as small as 0.5mm.
• Note: SDT103 Automotive Smoke Leak Detector has no air compressor or air pump inside.
• Features
• Built-in air pump: None
• Overheat Protection: Yes
• Pressure gauge: None
• Fault indicator: None
• Flow meter: None
• Flow adjustment knob: None
• Oil Drain Valve: None
• Liquid level gauge: None
• Air control switch: None
• Smoke control switch: Yes
• Adjustable pressure: None
• Intelligent digital display: None

WHAT CAN SDT103 SMOKE LEAK DETECTOR LOCATOR DO?

• Crankcase System Test: Excessive pressure or corrosion of the crankcase is the main reason to damage the seal of the crankcase and cause oil leakage.
• Intake System Test: Leakage in the air intake system will lead to insufficient intake of the car engine, which will result in scant engine power.
• Car Sealing Test: Poor airtightness of the car may lead to a lot of inconvenience like inability to keep warm dusty, not soundproof, and not waterproof , etc.
• Fuel Tank System Test: When there are gaps in the fuel tank and piping caused by improper installation or insufficient sealing of the fuel tank cap, it can cause leaks in the fuel tank system.
• Turbo Test: The leakage of coolant would cause the engine to report high water temperature.
• Various Pipe Fittings Test: Smoke testing of brake hoses, power steering hoses, cooling system hoses, air conditioning system hoses, turbocharger hoses, fuel hoses, intake and exhaust system hoses, etc.
• EVAP System Test: Leakage of the fuel evaporation system will cause fuel vapor to leak into the atmosphere, causing waste and pollution or unstable engine idling.
• Exhaust System Test: Unpurified harmful gases to be discharged into the atmosphere or increase vehicle noise is the main disadvantage when leaks happened in the exhaust.

PACKING LIST

• 1pcs * SDT103 EVAP Smoke Leak Detector
• 1pcs * Standard Cone Adapter
• 1pcs * Power Cord Clamp
• 1pcs * Valve Core Wrench
• 2pcs * Test Oil Refill Bottle
• 1pcs * EVAP Special Connector
• 1pcs * Smoke Hose
• 1pcs * Manual Book
• 1pcs * Packing Box

How to do leakage test?

• Step 1: connecting an external air source and a 12V battery.
• Step 2: Fill (baby oil or mineral oil based) smoke oil into the smoke machine. Note: The oil level shall not exceed the level gauge.
• Step 3: Disconnect the pipes that need to be conneced with detector.
• Step 4: Connect 12V vehicle power to start the device.
• Step 5: In about 30 seconds, the pipe will be filled with smoke. Check the leak points and use head lamp if necessary.
• Cautions
• 1. When you use this Car Smoke Leak Detector for the first time, fill it with 10ml baby oil. Please be careful NOT to beyond this range.
• 2. The testing liquid: both liquid paraffin and baby oil are OK.
• 3. Fresh oil can be filled with only when the smoke gets thin, and it can’t be filled over 20ml each time.
• 4. Before filling fresh oil, please pour out the left oil in the detector & replace the detector oil regularly.
• 5. During the process of leak detection, please keep away from smoke-sensitive parts.
• 6. Do NOT run the detector over 8 minutes continuously. It needs interval rest.
• 7. The round part of this detector has temperature, please be careful to avoid burns.
• 8. If the test pipe needs to be disconnected in the middle, please secure the other side with a rubber stopple.
• 9. Follow the instructions