Your cart is empty.
Your cart is empty.Product Description
Come with a Rod Magnet
Help control and put the small magnets into craft projects. Mark the magnet rod to to keep track of orientation. Would ensure you don't accidentally get your polarization wrong.
3-Layer-Plated Magnets
- 3-layer-plated
- Good corrosion resistance
- Great for crafts
Precise Size Control
- Diameter: +/-0.03mm tolerance
- Thickness: +/-0.05mm tolerance
Smooth Clean Surface
- Our magnets have smooth clean surface while others are bumpy or cut obliquely
Ray
August 18, 2025
These magnets all arrived strong as heck, no damage or chipping. The variety pack was great and gave me lots of options.
Customer
August 16, 2025
I used these for skitarii rangers. 3mm is a VERY tight fit for their small arms, but if you're careful and line things up correctly, 3mm seems to fit within even the smallest of arms. Totally worth it for the extra strength of these (relatively) larger magnets.Great bundle pack overall with a variety spread across the 3 sizes adequately. Should be enough to fully magnetize 10 units and all weapon options, and have all of the larger magnet sizes left over for larger models or vehicles.
CuriosityHound
July 29, 2025
Magnets came in a small plastic container that holds them well and with a N/S bar that makes it easier to handle the small magnets.My project:I bought a Seeding Square that proved to be a knock off from the real product. It didn’t come with a magnetic dibber or snap on funnel so the small parts are easily lost when moving from place to place.My fix:Using 2-5mm magnets in each leg I was able to attach the funnel to the back of the square where they hold onto a ring I made from a thin business card magnet -I used E6000 to glue onto the back.I used 4- 12mmx1mm magnets for the back of the dibber slot and drilled a hole to put a metal bar inside the dibber and covered both with water weld.It works well and I can take the square to the garden and not loose the parts. If I did the project again I might put the magnets into the dibber and put a metal plate on the back of the slot for them to attach to.NOTE: These are strong magnets for their size but the surface area puts limits to what they can hold. You can stack magnets together to make a stronger pull but after you exceed the width of the magnet stacking more won’t make them stronger. I decided 2 in each leg for 4mm thickness was adequate and didn’t add a 3rd for 6mm height stacked as the magnets I used were only 5mm wide.
freshkicks
July 27, 2025
Bought this to create a magnetic bit holder for the SAK Cybertool driver. I can confirm the 4x2mm magnet works great. Don’t need any adhesive or glue, just drop it in and the magnetic force keeps it in place within the cybertool driver. It creates enough magnetic pull to keep the bits in place perfectly. The 4x2mm size also is thin enough that with a bit in place the driver still folds perfectly.Quick tip, if you want to remove the magnet just insert the stack of 4x2mm into the driver and it’ll pull the single magnet out without issue. I was afraid the stack would get stuck in the driver but I’m happy to report that didn’t occur.Quick tip #2, place 1-3 of the 5x2 onto the inner flat part of the driver shaft and you’ll always have a few magnets to use for whatever needs you may have.Now the reason for 4 stars is the 3x1mm magnets are kinda useless. They are tiny and have weak magnetic force. I can’t think of any use for them unless you have very specific needs for that size.All in all happy with my purchase. I had very specific needs for it and it worked perfectly for the SAK Cybertool.
Pat
May 29, 2025
While small, these 8 mm x 2 mm magnets are proportionally strong and well suited to craft applications, holding art or info onto refrigerators or steel whiteboards, holding removable trim, and in particular, incorporating into multi-part 3D models. They arrived quickly, with none broken because they were well packaged. Actual measured size for the batch I received was 7.99 mm x 1.96 mm, close enough for anything I'm anticipating. FWIW, you can get stronger magnets but they come with a larger diameter or taller height. I choose these because they are stronger than the 6 mm x 2 mm magnets that are often seen in printable object designs, yet still fit a shallow hole so objects designed for them stay in scale. Caveat: I've only used in one project so far; I found they worked perfectly. I glued them into ABS with super glue (each flush with the surface per the CAD designed holes), and they are holding better than expected.
Customer
May 14, 2025
I use these to make materials for my students. Another teacher liked them so much that they asked for the link to get their own! I simply put a piece of duct tape over the magnet and attach it to the back of visuals/items and it makes the kids 10x more likely to use them—because magnets are fun!
Kelsey Carnell
May 4, 2025
These work great for my minis
Dulce Garcia
May 4, 2025
These magnets are good quality and quite powerful.
Bloxan
March 1, 2025
Super Top
Davide Mele
February 18, 2025
Ottimo prodotto e spedizione rapidissima
Luinias
February 12, 2025
Great and has a lot of usability
Client d'
December 22, 2024
Très bien assez puissants
Simone Z
December 17, 2024
Le calamite arrivano in un comoda confezione in plastica dove troviamo 100 calamite 3x1, 50 calamite 4x2 e 50 calamite 5x2 per un totale di 200 calamite. Le ho acquistate per utilizzarle nei modelli che stampo in 3d e sembrano fare il loro lavoro egregiamente.Il prezzo al momento dell’acquisto era di 10,99€
Recommended Products