Your cart is empty.
Your cart is empty.Titan 12047 Breaker Bar features a 1/2 in. drive head that swivels 180°. Heavy-duty chrome vanadium steel construction. Maximum torque is 335 ft/lb (46 kg/m). Chrome plated bar and black oxide finish head to resist corrosion. REPLACEMENT HEAD available: # 12021. Made in Taiwan.
H. Collier
September 2, 2025
I had to order a new wheel bearing and hub assembly for my Hummer H2 SUV and I knew I was going to need a good size breaker bar, and a big ass heavy duty socket, I thought I'd only need this breaker bar for just the bearing and hub assembly after I pulled the wheel off but it actually ended up that I needed it just to break loose the lug nuts on my wheel and man do it make short and easy work of all 8 of them, I mean I have a four way spinner but it was tough to break loose even one lug nut until I tried the breaker bar, so after that I did try to use my 1/2" drive ratchet which is big and heavy duty but couldn't break loose even one of the bolts until again I used the breaker bar, it took what would have been a near impossible task and made it much more easy, at first I thought maybe I should have ordered a longer breaker but nope this one worked perfect for my hard to break loose bolts and made it very easy to torque down the caliper bolts, the spindle nut, and the four hub mounting bolts so that I know they will be as tight as they should be and won't come loose on their own, so with that said if you have some frozen up bolts and nuts that you can't break loose then this bad boy will do the trick, I mean I use it to help with the swap out of a hub and bearing assembly that I otherwise would t have been able to complete without this bar, I probably could have broken one or two loose with my big ratchet and a ballpeen hammer but I'd probably still be out there right now trying to replace my hub assembly, and now that I own this bar I can use it to replace my other wheel bearings so they are all brand new and matching, the only con I can think of is that the head is kind of loose, like maybe it could use a thin washer between the body and the head so it isn't so loose, but with that said it did still work very well and got the job done and got it done so much easier then it would have been otherwise so I would recommend this to anyone needing som extra torque
Mike
August 30, 2025
I used this with a lineman socket to install 8-30" long 4" helix earth anchors for a small cabin. A couple of the anchors hit a tree root and wouldnt budge anymore. And i reefed on this thing with everything i had(300+ lbs man) and while it bowed, it didnt bend nor did it break. I have since used it to completely rebuild the front suspension on my truck and it performed flawlessly.
David Brown
August 19, 2025
I have 65mm nuts to turn with this - the breaker bar pushed about 250 LB torque no prob. I could feel a little flex in the steel shaft, but it held. No flaws in this construction - this is not cheap junk metal far as I can tell.
Brandon Ohta
August 9, 2025
Finally found a long enough breaker bar, weight is heavy. I really like it.
J
May 11, 2025
I'm a home DIYer, not a professional so I don't use this tool a lot. In a year, I've used it three times. It is a heavy tool and it worked the first two times. Today, I was using it to remove a screw out freeze plug on an engine to install an engine block heater. The swivel head on the breaker bar broke. I don't think the swivel head is strong enough to handle the torquepressure that a 30" long handle can create. I'll upload a picture of it.I decided to look up the warranty on this tool on the Amazon page where it is listed and didn't find any information on a warranty other than this --- "Warranty, Parts: Parts". I don't know what this means. Is there a warranty on this tool? If so, what is it and how is it used?
Banner
April 14, 2025
Used the breaker bar to loosen two axel nuts, and it worked fine.
Glen E Thomas
April 3, 2025
I have struggled for years with a short 1/2 inch breaker bar with a pipe as leverage. Decided to go with a long breaker bar and I am pleased with the quality of this breaker bar. Can't go wrong with the price and a pleasure to use compared to the pipe meathod. Should have picked this up years ago.
Max
February 12, 2025
So far I've used this breaker bar to effortlessly remove the 22 mm nuts on a Toyota Camry's front struts, as well as some tougher ones like the rusted nuts on the same car's(1997) exhaust manifold. The manual warned that penetrating fluid was necessary. With this breaker bar though, my wife was able to crack them off with little effort, sans any fluid. I've also used it to loosen lug nuts, but those don't take much effort even with a shorter bar.One important note though, is that you never ever use this to tighten something. You can easily exceed the torque specs for whatever you're tightening, resulting in something breaking.
Aziz
January 4, 2025
Very Good and Robust build capable of any intended Job.Unfortunately It is too long to fit inside my Red Snapon 26 inch toolbox.I will miss this beauty. 🥲
Recommended Products
