Your cart is empty.
Your cart is empty.Product Description
Enjoy the UNREAL moments that Tyger Auto driven with the innovative gears.
TYGER TRUCK FENDER FLARES
Whether you are looking for factory style classic truck fender flares or a more eye-catching pocket bolt-riveted style fender flare, you’ll find them right here at TYGER Auto. Our truck fender flares are made with impact-resistant polypropylene, reinforced by well-developed injection molding technology.
TOUGHNESS COMBINES WITH GREAT LOOKS
This is where toughness combines with great looks. Not only that, but these bumper flares are also high-quality and easy for any vehicle owner to install themselves.
EASY INSTALLATION
Average install times of TYGER Auto fender flares range around 1 hour with minor drilling required, and are compatible with aftermarket bumpers, and the fender flares are backed by our industry TYGER BRAND. Shop our vast collection of wheel flares to find the perfect product to add to your vehicle as you make some DIY upgrades.
TYGER AUTO - Driven by Adventure
Founded in 2013 in California, Tyger Auto is a proud car culture innovator powered by a group of American and Canadian adventure seekers with lifelong automotive parts experience.
Our mission is to introduce innovative designs that emphasize excitement, reliability and value to car owners.
Caiden
2025-08-28 13:02:32
These were stupid easy to install, they fit right up and made my truck look better. And covered up that rust spot! (Ifykyk)
Daniel S
2025-08-22 16:18:45
I wish all aftermarket products were this good. Perfect fit both front & rear for cateye chevy. 5 min install, no warps, no misalignment, simply perfect and looks factory / oem
Honest Reviews
2025-07-22 13:46:47
I had a mostly great experience with the Tyger Auto Fender Flares (TG-FF6C4218) on my Chevy Silverado, but unfortunately, one major issue dampened my enthusiasm.The fit and finish of these flares were impressive right out of the box. The fine-textured, paintable surface gave them a clean, factory-style look, and installation was straightforward with all the necessary hardware included. They fit snugly, and I was happy they enhanced the truck’s appearance while providing extra protection.Mostly, these flares held up well against daily driving conditions. They stayed secure through rain, dirt roads, and normal highway speeds—until one of them didn’t.Unfortunately, one front fender flare blew off while driving down the highway. That was disappointing, but what made it worse was the fact that Tyger doesn’t sell individual replacements—you have to buy an entire four-piece kit just to replace one flare. Since I only needed one, I wasn’t willing to spend the extra money on a full set. Instead, I removed both front flares and kept the rear ones, which have held up perfectly.
Sean Kent
2025-07-17 21:43:06
Really nice quality. Not that expensive, thought they might be cheap. But really really nice quality. So easy to install. Looks great completely changes vehicle
way2muchstuff
2025-07-09 17:13:32
Couldn't ask for a better fit on my 2002 Silverado, but some adjustments were needed. These fit perfectly into the wheel openings, no slop or gaps, snug. A person could stop right here and just screw them in with a set of stainless screws as you would with a set of mud flaps and forget the buttons. (In the end if the buttons fail, this will be my permanent fix). And be done with it.They should be pulled tight to the top of the wheel opening, then visually find which vertical button will hold it in place tightly at the top. My top buttons did not line up and needed to be slotted slightly so the hole in the flare would match the hole in the fender. This was the same on all four flares. The top two holes did not match without a bit of adjustment. Bear in mind this is also an opportunity to put inward pressure on the flare for a tighter fit while checking how much and in which direction the new hole placement should go. This will keep the flare tight to the body without any gaps.I used my Dremel with a high speed cutter bit #194 on low speed to slot the upper mounting holes in the flare roughly 1/2 of the hole diameter and slightly angled to the outside (to increase tension and close any gaps or looseness). I had a single plastic pin securing the flare in one of the vertical holes that fit best. The instructions suggest installing the top pins first and working down. These did not line up in my case, and required slight slotting by being roughly 1/2 of a hole off. Better to find the best vertical hole after pressing the flare tightly upward into position.The gist of this is that these flares can be fitted perfectly with only minor adjustment. As far as the buttons included, hope they survive a winter ice load but can be remedied with some stainless screws for a permanent fix.
Customer
2025-07-01 18:20:08
Fit and finish was great
Jeff
2025-06-09 17:11:42
I don't often write reviews unless a product exceeded my expectations. This is one of those. Delivered in two days, and took all of maybe 20 minutes to install all 4 fender flairs on my Silverado. Super easy and they look fantastic. All for $75.00If you're thinking about these, go for it, you won't be disappointed.
Rick Huber
2025-05-14 13:54:47
Fit perfect on my 2007 GMC
Mary Mantha
2025-03-22 10:00:48
Bought these for my 2000 Sierra. I painted them to match the truck. The fit was great and the install was very easy.
Kevin
2025-03-13 17:37:59
Easy to install and very affordable
John.S
2025-03-10 10:17:27
Used on the box of my truck as I put a new box on. I would recommend to let them sit in the sun for a while so they fit better. But very good product looks like the factory ones, would buy again if needed.
Miles C.
2025-02-28 14:59:34
I just received these today and started to install on 2002 GMC Sierra long box. The whole job took me three hours for a set of four. First had to remove the mud guards and then start to install the flares. I also used black caulking to finish them off. I would really recommend Tyger flares. 1. They shipped quickly and with no damage to contents. 2. Flares were well packaged and marked for the correct fender. 3. More than sufficient hardware is provided. 4. I chose to put the bottom of all the fasteners in first and then install the plastic drive screw. 5. Flares fit well with some gentle pursaion. Use an awl to help to line up the holes. All in all I am satisfied. Thank you for a quality affordable product.
glenn daly
2024-11-19 15:09:08
Easy install cost effective way to improve trucks look
Recommended Products