Your cart is empty.
Your cart is empty.Product Description
Matthew A.
2025-09-03 13:03:02
I couldn't be happier! These fender flares look like they came factory installed and were a quarter of the price!Installation instructions were better than most, but still reqired some concentration and common sense to decipher.No drilling was required and all the parts needed for secure installation were included.If you want an OEM look, these will please! I am very satisfied with my purchase and highly recommend!
Chris Stolp
2025-08-25 12:29:33
Nothing in the. I’d to tell u how to mount them. No hardware for mounting. Terrible
E. J. Feulner
2025-06-25 18:29:47
I literally never write reviews but hopefully this info will help some people in the future. I ordered the OE style as I want some matte black pieces to offset all the chrome in my new truck.First these were significantly less expensive than all the US truck aftermarket parts companies. Yet they seem to look very similar in size and appearance.Most important tip: when putting the rubber gasket seal on the flares leave the red tape cover on and then as you push it on peel the red tape cover off every 9 inches or so. The first two flares I peeled the tape cover off before I put it on the plastic and it was a total pain. Once I tried the new way I got the rubber on the two rear flares in literally three minutes while the front two took 45 min each.Second tip: loosely secure one of the screws at each end as the first step. This makes it so much easier to then locate the other holes and feed the screws into the clips. Even the clips you have to add you can slide them around behind the flare to get them lined up. No reason to mark them first with a grease pencil like the instructions say since the black rubber squares that protect the paint from the new clips doesn’t stick anyway. So put the black square on then the clip close to the right spot then hold the flare tight to the fender and move the clip around behind the flare until you get the holes lined up.When you are first securing any/all of the screws and bolts leave them all secured just enough to not pull out. Then once they are all loosely started push the flare tight to the fender with one hand and tighten the bolt/screw tightly with the other hand.If you removed factory mud flaps like I did hopefully you saved the bolts and clips as this kit assumes you have those bolts and clips and does not have extras.I have no idea what the white plastic trim tool is for at the end of the installations steps. If you secure the rubber gasket with the long edge on the inside of the flare it’s barely visible on the outside and actually looks nice. See zoomed in pic above with the red arrow pointing to the gasket.I would say if you’re looking for an inexpensive set of relatively small, matte black fender flares this is a good option. Good luck!
G R
2025-05-16 10:32:32
The media could not be loaded.
David Stanley
2025-05-03 11:23:59
Honestly, I was skeptical about putting these on my 2022 F-150 FX4. But after taking my time (about 3 hours to install), I couldn't be happier. I wanted some protection for my fender wells and this product really does look fantastic after installation. There's another review on here (4 star) that has some really good installation tips. Durability is yet to be determined, but the install seems very secure and sturdy. I would buy this again.
Renato
2025-04-06 16:55:17
It damaged my running boards, it fit and look good, but doesn’t work with trucks with running boards, maybe is set only for fixed step trails.
Jim
2025-03-29 17:23:57
I wrecked my truck back in the beginning of the year and I was looking for the OEM fender flares and I could not find them anywhere for a cheap, but I found these and I was shocked by the price and the quality of them! You can find any at a cheaper price anywhere! The only thing is that there is some sort of weird coating on the flares that makes it hard to paint even after sanding. Other than that they are literally perfect!
Derek Dimond
2025-03-13 11:36:37
These aren't too hard to install but they referenced reusing 4 existing bolts on each of the front fenders that my truck didn't have. My 2023 F150 had the metal holes but didn't have the speed nuts or bolts that the instructions say to pull out and reuse for the mount. I had to buy the parts for another $20 but then everything else went together smoothly. They look great on the truck and fit the contours like factory. Overall a good deal for the price but I wish they came with all of the parts needed.
Ron V
2025-02-20 17:09:08
install was easy and looks like they were always on the truck
RG
2025-02-15 13:51:46
This is only a replacement for factory installed fender flares. If your truck doesn't already have them, you would have to drill holes. I specifically bought these because a reviewer with my same truck said "no drilling required".
Recommended Products