Shopping Cart

Your cart is empty.

Your cart is empty.

2' Inch Drop Spindle Front for Belltech 2100 2WD for 1982-2004 Chevy S10 / For GMC Sonoma Jimmy S15 Pickup For 2WD model only

4.5 (8) Write Review
Free shipping on orders over $29.99

$131.99

$ 59 .99 $59.99

In Stock
  • 【Vehicle Fitment】: For 1982-2003 S-Series 4 & 6 Cyl.Std & Ext.Cab For 1983-1997 S-Series Blazer/Jimmy For 1980-1988 Olds Cutlass, 442, Salon For 1980-1987 El Camino, Sprint, Regal, Grand National
  • For 1980-1987 Malibu, Monte Carlo SS For 1980-1987 Grand Prix, Lemans For 1982-1986 Pontiac Bonneville For 1980-1981 Buick Century (Does not fit 1998-2003 S10 Blazer)
  • 【Note】: These Spindles Are For 2WD ONLY!!!They Will Not Fit 4WD Models
  • 【Part Number】: For Belltech 2100, Chassis Tech SPI-CV82XX, CPP DT-100228, DJM DS2031-2, Groundforce 6002, MaxTrac 100120, McGaughys 33122, Western Chassis 12100
  • 【Warranty】:Ten Years


Product Description

Y02-040-1

  • Description:

These spindles will lower the front of your vehicle by 2". It is the easiest way to achieve a 2" drop on the S10 / S15 and provides the best ride.

Y02-040-2

Compatibility

1982-2003 S-Series 4 & 6 Cyl.Std & Ext.Cab

1983-1997 S-Series Blazer/Jimmy

1980-1988 Olds Cutlass, 442, Salon

1980-1987 El Camino, Sprint, Regal, Grand National

1980-1987 Malibu, Monte Carlo SS

1980-1987 Grand Prix, Lemans

1982-1986 Pontiac Bonneville

1980-1981 Buick Century

***Does not fit 1998-2003 S10 Blazer***

Y02-040-3

Note

  • These Spindles Are For 2WD ONLY!!!They Will Not Fit 4WD Models
  • Vehicles with 8" wide wheels with require using a small wheel spacer to have clearance between the rim/tire and tie rod ends.

Y02-040-5

Part Number

Belltech 2100, Chassis Tech SPI-CV82XX, CPP DT-100228, DJM DS2031-2, Groundforce 6002, MaxTrac 100120, McGaughys 33122, Western Chassis 12100

Attention

Please use appropriate shop manual for your vehicle to obtain specific service instruction. If you do not have an installation manual or not enough skill to install this part, it is recommended to seek the help from a qualified mechanic.


norman dupont
August 24, 2025
They work fit easy to install
Wayfastwil
August 6, 2025
Well made product needing a small amount of clearancing you could do it with a Dremal to
Luis lulu
July 9, 2025
This product it's not a bolt on, there are parts that bind, you will have to modify either the upper control arm or the part it self, the original bolts are metric for the dust cover and speed sensor but on the spindle they are all standard 5/16 thread. The milling is not correct one of the spindle grooves was not milled to accept the washer and did not fully seat to preload the bearings. Not satisfied at all, I have modified and milled the spindle to make it work properly, in all I have spent 4 to 5 hours on mods and finding fasteners to make it work in all im satisfied with the height and that's all im satisfied with.
Bruce
July 5, 2025
Rub on upper an arm, put ball joint on bottom of a arm or grind. Could not tighten rotors without adding shims between the spindle nut washer and bearing. They are not BellTech
Toby Shoda
July 3, 2025
Parts were what I ordered. Came delivered and packaged well. Fit was good with no modifications.
Tony
April 7, 2025
I ordered a set of 2” drop spindles but received stock spindles. Was told to contact the manufacturer. I’m out $125. Buyer beware
james hudson
April 2, 2025
Fitment was poor. I was able to make the passenger side work. The driver side the shaft the rotor mounts on is completely wrong size. My window for return ran out. Now I have to buy a different set
Kody
January 3, 2025
Rubs the upper control arm not a big deal but tie rod end tamper it bigger then the tie rod end