Shopping Cart

Your cart is empty.

Your cart is empty.

Big Horn 11741PK 4-Inch Key Hose Clamp, 5-Pack, Colors may vary

Free shipping on orders over $29.99

$10.99

$ 4 .99 $4.99

In Stock

About this item

  • Product type :TOOLS
  • Package dimensions :4.800 cm L x13.004 cm W x14.706 cm H
  • country of origin :China
  • package weight :0.319996lbs


From the Manufacturer

Our 4-Inch stainless steel Key Hose Clamps hand tighten for a leak-proof seal, even in tight spaces. No tools required. 5-Pack.


JLF
August 26, 2025
Great value for a lot of product. Works great to hold the tube to my dust collector. I can find more uses for the additional sets this came with. Easy to operate and works great!
Boxtakilla
August 25, 2025
I bought these clamps to fit a 4 inch hose to my dust collector and power tools. They work well and make it easy to move the hose from tool to tool. Much easier to work with than clamps that require a screw driver to tighten and loosen.
J. Whiteside
July 19, 2025
These are pretty straight forward, so I'll keep my comments somewhat brief. You'll obviously need this, usually for a workshop, to clamp down your typical 4" dust collection ports to a fitting, device or coupler. As for my experience, it's been overall pretty good and haven't had any issues to report. I really like the finger nut, it does a good job getting nice and tight and I haven't had any loose fittings...which I suppose is the metric you'd judge a hose clamp on. I definitely prefer this design, although I will admit I don't often remove the clamp as I've used primarily friction based fittings for moving my hose. The other good thing is you get quite a few for the money, so it's a pretty good value overall. I only needed a couple for my purposes, but have a few spares in case they break or I extend my dust collection needs at some point in the future. Not much else to add here...except that I'd definitely recommend them!
Griff
July 18, 2025
So far so good. The only draw back is the time it takes to loosen or tighten. Some type of "over-center buckle" type clamp might be better, but these are inexpensive and ok.
NVmike
July 16, 2025
If you're trying to use for smaller then 3.75 in these will not work. I wish they would post the measurements! Junk I've reached out to there customers support. No answer!
Symbols Of Love
April 29, 2025
Pretty much the perfect clamp for dryer vent hose or any other vent of similar size requiring an easy way to tighten them in an awkward spot/location. NO TOOLS REQUIRED! Perfect.NOTE: If you appreciated this review please give it a “thumbs up/like” your helping me to continue to give honest/unbiased insight into products I’ve used and you may have questions about. Interested in a product but don't know enough about it and would like it reviewed? Please let me know and I'll see what I can do... Thank you 🙏
Brett
April 4, 2025
It is a hose clamp. It clamps hoses well. I love the key feature, no screw driver at wired angles to secure the clamp. And, most importantly, this thing tightens up well. I used this to direct the dust from a power tool blower that is very powerful and the clamp secures the hose no problem.
Alan Dale Daniel
March 25, 2025
These are outstanding hose clamps. The fit easily over 4 inch hose fittings. The inside diameter is about 4 7/16 so there is almost a half inch to spare over the size of the 4 inch fittings. The knobs are a good size and turn the steel bands easily once they get started. The first 10 or so turns is very hard, but then the going gets a lot easier. They clamp tightly. I have significant arthritis in my hands and I could still manage to turn the knobs and snug them up enough to hold well - at least against my attempts to pull them loose.I highly recommend this product.AD2
THC-ThatHighCandian
January 30, 2025
Work better than and higher quality than grow tent ones and are cheaper what’s jottni ovoe !!?? 6/5 if I could !! Thank you!! Again!!!1 came bent from postage as well as was only a 4x pack .. I can’t return or get replacements past 30 days :( guess I’m stuck with them ! :(Edit: yeah I’m stuck with the 4 I should of gotten 5! But managed to in bent just tighten to a ducting fan end /(any hard 4 inch round object Metal) will fix itThese work phenomenal for fans and ducting and boosters and carbon filters excetra’
Bruno
January 20, 2025
Excelente caldad
Larry Bernais
January 18, 2025
great clamps, easy to use. a must for any clamp you remove often
Luis BETANCOURT
January 6, 2025
Bien!
Gavin
December 2, 2024
Does the trick