Your cart is empty.
Your cart is empty.Product Description
Karl B.
August 27, 2025
Bought this to work on my 2001 Suburban but had to use it on my sister's 98 Suburban. Bad Pitman arm. That setup is pretty tight so our other puller wouldn't fit. Got this one in place and it fit perfectly and popped the arm out of the center link with no strain!This product is solid and well built with a great price. However, as with ANY threaded puller, make sure you add a good lubricant to the threads before you use it. It does ship with a preservative oil on them but it needs a good coating of lube before each use to ensure no damage to the threads of the screw or body of the tool. Do that and this unit will give you a long and good service life!
Family4Life
August 25, 2025
I had to replace all the suspension arms on my 2013 Mercedes S550 W221 Base, and I needed a ball joint separator for the job. So I gave this one a try, and it worked like a champ. It fits very well in tight spaces and pops the ball joints very easily without any damage. Although one may be tempted to leave the inner cap nut on and push the ball joint with it, I had better results removing the cap, and letting the ball bearing in the center of the push pin do its job preventing any slippage. This tool design works better on my car, and any other car for the same job than the fork-pressing tool. And the price is just perfect. Don't waste your money getting a similar but more expensive tool, this one fits and works on Mercedes like the more expensive one does.
Kenneth B Humphrey
August 20, 2025
The ball joint separator did not break loose my joint. It just broke. It feels heavy and well made but a complete break like shown in the pic reveals substandard material.Do not buy.
Juan Z.
August 16, 2025
I received exactly what I expected! A well built tool! Worked beautifully! I would recommend
Jennifer Plumb
August 12, 2025
This item worked good. Husband was quite amazed.
Senior Leigh
August 9, 2025
The spectator is good
niceguytwo
July 3, 2025
I was changing the CV axles and ball joints on a 2006 Mountaineer and needed to get the lower control arm removed. I tried many different methods and tools without success. I finally ordered this tool and within minutes I was able to separate the control arm from the ball joint. I also tried it the tie rod ends with the same success. With the lower control arm removed I was better able to replace the CV axles and the worn lower ball joints on both sides. I do recommend leaving the nut on the end of the studs. It makes it easier to line up the clamp and you won't damage the threads. This tool has saved me many hours of work. Very happy with the results.
Hughborg707
June 19, 2025
I used this on my BMW X5 E70 to pop the joint of the thrust arm. One tip is to remove the inside cap, nut, whatever you want to call it. It has a pin that fits right in the hex wrench hole of the bolt of the joint. I used a socket wrench to tighten it up and a few turns and let it sit. About a minute later it popped right out.The tool is well made and has a thin fork that fits my vehicle perfectly.
stephane bergeron
May 31, 2025
Pas utilisé encore mais j'ai été surpris du poids séparateur de rotule. À suivre
Peter J.
May 9, 2025
To pull the steering knuckle from the front lower control arms, every YouTube video on this year and model car recommends prying the aluminum cast steering knuckle apart. I used a pry bar and didn’t have much luck in the tight space of the fender well. I bought a cheap “steering knuckle spreaderâ€. Finally, I used this and I slowly cranked it with a 3/4†wrench and it smoothly worked the stud of the ball joint out of the steering knuckle. It didn’t reach all the way so I put a socket between the bolt of the spreader and the ball joint stud just to add some length and it eventually pushed the ball joint all the way out. This was worth every dollar. I had another, much larger ball joint press but it was too large to fit behind the steering knuckle and this worked perfectly.
Customer
March 13, 2025
Received a damaged a previously used tool..not impressed needed for a coming job and was told could not exchange only return.
Tahir Elsaidi
February 9, 2025
it worked perfect to remove the broken rear wheel stud out of the hub in my jeep wrangler JK 2011 . This separator pushed the broken stud out of the hub easiy while hammer could not do it .
Reza Khalesi
February 6, 2025
I use this tool to release ball joints. It is working very well and easily. So I recommend it.
Recommended Products