Your cart is empty.
Your cart is empty.
RSVP strives to offer quality kitchen products and cooking tools at competitive prices. These Cheese Slicer replacement wires are designed to fit our RSVP Polished Marble Cheese Slicer in Grey (item #GRY-5). Each slicing wire measures 5-inches in length. When all the right people, and ingredients, kitchen tools, and food come together, we call this The Art of Gathering. No matter how you slice it, we love cheese here at RSVP International. If you love cheese as much as we do, our kitchen gadgets and accessories are a must have in your kitchen. Whether you’re slicing, grating, or serving, we have all the kitchen gadgets and cheese accessories you need to create the perfect cheeseboard or add some cheesy goodness to whatever you’re cooking.
Pamela
2025-08-28 14:24:29
Fortunately these RSVP International GRY-5 or #WMCS Replacement Wire's fit my cheese slicer made of marble with a slot perfectly. It was easy to install and works very well for slicing. The quality is good and it's nice to have a spare in case down the road the one in the slicer gives up the ghost. I would order these again.
Norwenna
2025-08-17 11:18:30
Edited to add: I've had one of these wires on my cheese board for three and a half months now, and I use it to slice cheddar cheese at least once a day. Today the first wire broke, which I think is not so bad. I installed a new wire pretty quickly this time.I hesitated to buy these wires because I didn't know if they'd fit my old cheese board. They did fit and I'm glad I took a chance. There are instructions how to install the wires on the back of the package they came in, but I couldn't figure out what the instructions meant, even though they were written in good English. I looked at other customers' instructions in the questions section here and I still could not understand. All this despite the fact that I've replaced the wire before, with the spare that originally came with my cheese board, using reason and common sense. I finally got it this time sort of by accident. I hadn't realized that in spite of the wire being at a 90 degree angle to the board, the wire turns 90 degrees when you just tighten the knob. I still don't quite know why, but I'm happily slicing cheese again for the first time in months.
Jim S.
2025-08-10 13:12:58
It does the job, but, I wish it was a bit shorter so there is a bit more tension on the wire. Perhaps my ancient marble slab cutter may need to be replaced before I use up the 4 spare I now have.
Dick Snyder
2025-07-08 10:54:00
The wires fit perfectly.
J. Bailey
2025-06-20 18:43:18
These are exact fit for my marble cheese slicer. Measure yours and make sure it is the size required in the text of this product description. When you install, be sure to tighten the handle as tightly as you can so it doesn't rotate on the metal U-shaped hinge arm and loosen the wire. Also, make sure the wire goes around the top of the circle "pully" so the wire is tightened as you press down on the handle. One adjustment I had to make was to slightly re-shape the U-shaped hinge arm so the wire was tight and the hinge didn't scrape the edge of the marble base. This was simple to do by pressing it against my kitchen sink. Don't overdo it; it will yield but make small adjustments. I was sure I could fix my slicer by "simply" getting some stainless wire, but that was more expensive than these replacements, and it would have required monkeying to make the loop ends.
Marty A.
2025-06-10 17:03:54
These replacement wires will work for any marble top cheese slicer that is 5 inches wide. The package comes with wire installation instructions but I also added mine below.Unscrew marble handle B from retaining nut C ('stainless steel donut') and remove the D shaped arm away from the cheese slicer.Remove old wire from the D shape arm A.Slide base of D shape arm A into bottom of cheese slicer and loop one end of the new wire around the the groove at the base of the arm A.Slip the other end of the wire onto the threads of the marble handle (B). Screw the marble handle back onto retaining nut C.Position the new wire on the bottom of the retaining nut C.Slide retaining nut C onto arm A and swing the arm A down to aligning wire in grooveTighten wire by adjusting angle of marble handle B and tighten the marble handle clockwise.When the wire is taut, screw in handle until it locks against arm A through the retaining nut C.Store the remaining new wires in the original package and note the location on a piece of paper (small sticky note) at the bottom of the cheese slicer.
Lindsay Clark
2025-05-01 15:25:36
Wrong size won’t fit my marble slicer
Ted Kochanski
2025-04-08 15:07:56
If the tension is kept "taut" like guitar string then it cuts cheese with ease -- tendency to lose tension then the cutting is poor and the wire may break
Rick
2025-04-07 12:00:45
already answered the question .
Allen Anderson
2025-02-08 21:59:28
Although not the direct replacement part, it does work with my Artisanal Kitchen Supply cheese slicer. The ends are a little different and require a bit of finesse to get them in the slots, but it does work.
ANA
2024-12-12 17:29:16
Lo tuve que adaptar pues mi cortador no es el mismo para este tipo de repuestoPero me sirvió perfectamente
Lorraine Durand
2024-12-07 18:50:09
These arrived within delivery dates, are easy to fit and work well. Saved a slab of marble going to landfill!
MJ Ramirez
2024-12-02 16:37:31
Excelentes
Recommended Products
