Perfect fit for my 2011 Ram 1500. Easy install. My wheel wells (quarter panels) were badly rotted. Slapped some Bondo, heavily, covered it all with these flairs. Also, drilled flairs onto panels attached with sheet metal screws. Really tight and secured. Should get another 5 to 8 years of good looks

I bought a truck for $6K and decided to mod it on the cheap. I ordered these fender flares mostly based on price as they were WAY less money than most of the others. I was prepared to be disappointed given the price point but hoped for the best. I was more than pleasantly surprised to find out these were high quality, including the hardware, the instructions were clear and thorough, the install was straightforward and the fit and finish are excellent! I would recommend these to anyone looking to add some quality fender flares to their truck regardless of budget.

Makes our truck look kool! Fairly easy to get on. 2013 RAM 1500

I am overall impressed of how they look and happy about my purchase, but the screws included were far too small, had to use some extra we had. They seem to be sturdy and they look great.

I installed these on my 2014 Ram 1500 Crew Cab 4x4....Conclusion- I had already removed the badges/emblems from my truck years ago. You will have to remove/relocate the HEMI badge for these. I am VERY happy with the outcome of these flares. In all, flares and paint, I am into them less than my buddy spent on his big brand flares, that look identical to me, and his aren't even painted. I know paint cost varies by location but I went to the same shop my dealer uses for body repair so I am confident the paint will hold up. Only time will tell how the flares themselves do but I would recommend them even though they affect the badges, if you have them.Packaging - The box was smashed in on the side. Nothing was damaged and everything was accounted for. One recommendation to manufacture would be to add a block of foam to fill void in the center of box or stuff with shipping paper. Each flare was wrapped in bubble wrap and easily identified.Product - My buddy had purchased another, well known, brand and spent a little over $400 on his. I helped him install them on the same type of truck as mine. I compared these to his and side by side I could not tell a difference. Aside from his being on his truck, unpainted, for a few hundred miles. These Tyger flares were very very hard to tell apart from his. I would say I didn't notice a difference but others may. The rubber strip that goes against the truck looked the same and the installation method was the same. The Tyger flares do not use all of the holes that are in the fender well. This would be the only change I would recommend but never the less the seal was good and tight. I opted to take these and get them painted to match my truck. (The auto body shop I took them too even confused them for the more expensive ones.) The shop told me they sealed them, applied a flex coating and then painted and cleared coated them. There was no problem getting anything to adhere to the material the flare is made of. The result was an OEM looking paint job on them.Install Prep - I brought them home and let them sit a few days before I had time to install them. I opted to paint the bolts and flat washers gloss black (they are real metal bolts and washers, not sure if they are stainless). I prepped and painted them with rattle can high heat BBQ grill paint. You are supplied with a Torx bit for the head of the bolt. I had initially planned on using blue thread locker on the bolts (we did on my buddies more expensive flares because the bolts kept coming loose.) I was happily surprised that the supplied nuts with the Tyger flares were nylon lock nuts. So I did not use thread locker. The bolt install was slow, mainly because I went slowly so that I did not chip the paint on the bolt or dimple the paint on the flare by over tightening. It was very easy to do though. The rubber seal was the worst part. Not because it was unusually difficult but the process is slow. I felt the provided instruction covered the process adequately. I would only add do the two rear flares first. This way you get a fell for how it works and there are no cuts needed like on the fronts. Be careful I was concerned I wasn't going to have enough rubber seal to complete all four flares. I DID have enough but there was only about a four inch piece left over. So there is little room for error.Install on Truck - The supplied instructions were adequate for this as well. I had to remove a couple extra factory wheel liner screws that weren't in the instructions but this was to be expected due to the slight variations in make, model, and year of the trucks. It did not affect the fitment at all and was easy to spot using some common sense. The seal was tight all the way around the flares. No gaps and they fit the body lines perfect.

Would buy again if needed they come with everything you need and extremely nice

Look great and easy to install on my husband's truck. I did it for him by myself!

Nice product, EZ install, They add so much to my truck, turns heads now that they are on . Great fit .

I was skeptical to buy these, but quality is great. All the comments about gaps should be taken with a grain of salt. The main Key is HEAT! Let them sit in the sun before you put them on! Then let the truck sit in the sun and it actually gets better. Finally, I used a small clamp and small block of wood to suck it in towards the fender where any soft tapping with my finger revealed it could go in more. Than just loosen and re- tighten those bolts and remove clamp! Perfect! They look great too, not cheap. Just remember you will have to remove the front hemi badges. Use heat gun and fishing line towards badge side. Then attack the rest of the adhesive with badge off. Buy some 2inch double sided 3m tape on here and a small exact to cut around the lettering. I used tape to mark where the badges were before Taking them off, then left tape in Place. THis made lining them back up straight super easy

Easy to install. Fit perfect. Good price. Would recommend

Encajaron perfecto sin el plástico interno, los tornillos no quedaron, se necesitó comprar unos pero las cantoneras quedaron perfectas, muy buena calidad por el precio.

Seller definitely making good profit on this product. Twice the price of the smooth version for my truck. Tyger pricing on their website is the same whether it’s smooth or textured but they don’t ship to Canada.That being said, it was still worth it. Very good quality. Nice texture. Looks great. Excellent fit on my 2020 Ram 1500 Classic. Had to remove Hemi badge but I knew that when I ordered it.

I installed the fenders on my Ram 1500, 2013. I had to remove the badge “Hemi 5.7L”. It was pretty easy to perform, truck looks pretty good.I’m happy with the result.