Your cart is empty.
Your cart is empty.Criditpid 326628-761 Furnace Draft Inducer Motor Replacement for Carrier, Bryant, Payne Models, Furnace Blower Motor Exhaust Vent Venter Motor.
Customer
August 25, 2025
Easy to install, fit perfectly and runs well
neli magradze
August 18, 2025
Works great so far no complaints
Customer Since 2008
August 11, 2025
My Bryant Furnace is about 20 years old and the inducer motor (326628-461) is dead. I could not find one with the same model number and instead I ordered this one. It arrives in just in two days with all parts in well packed. It contains wire adaptor which connects the old interface as well. Installation is easy. The only thing I have to adjust is the ground wire is a little short, I have to cut a piece from old unit and connected it to the new ground wire. In the first a few days it makes some noise. After a few days the noise was gone. So far after one month, it works well.
Jim G
August 6, 2025
I had an issue with my Bryant Furnace making a horrible noise. This inducer motor was clearly the issue after doing some research on the internet. Basically, required 3 screws to be removed as well as removing the power connector from the motor.Only challenge I ran into initially was when I put on the fan that assembly it came with, I had it too tight to the motor which caused it to seize up and not spin. Allen wrench adjustment fixed this. Finally, the fan needs to spin freely and if the motor is not re-attached exactly correctly, it may be slightly rubbing in the interior area causing it to not spin freely as well. Once these two things were resolved, all good.No issues on shipping or quality of motor and parts.
brian zachrich
August 3, 2025
Fit my Payne furnace just fine. Nice and quiet my old fan had bearings going out. Wire adapter was spot on to what my furnace needed.
Derek D.
July 25, 2025
Installing was effortless as everything lined up and was an exact match. Unfortunately after two days it completely quit running resulting in me having to install my older unit.
Ralph Simoni
July 12, 2025
Fixed heater 👠quite and exact replacement
Db
June 3, 2025
I really love this
MJM
April 13, 2025
Unit arrived very quickly well packaged. Good quality bolt in replacement. When ordering I had a question as to the different suffix numbers which wasn’t stated on the page so here is what I found with the enclosed paperwork. 326628 is the kit the -760 is for a 45,000 or 70,000 BTU input -761 is the same -762 is for a 90,000, -763 ,-764,-765 are for 110,000,135,000,155000BTU furnaces. These are to replace a single stage inducer motor and come with a special pigtail to make this kit work with a single stage application.This kit will also work with a two stage inducer motor application. Same 326628 kit the suffixes are slightly different. -760 is 45000btu -761 is70,000btu,-762 is 90,000btu, -763 is 110,000btu,-764 is135,000btu,-765 is 155,000 btu. Hope this helps.
Customer
March 13, 2025
Inducer shipped fast, would deal with again
Bought stuff
March 3, 2025
This was easy to install and took only 5mins - took more time to get the cover off and find a place to set it down 3 bolts gasket and the wire clip
Kevin
February 16, 2025
Our furnace stopped working because the existing draft inducer motor died during a cold snap where outside temperatures were -20c. It was a Saturday 2am in the morning break down, we called 4 different companies but they would not be able to get parts until maybe Monday or Tuesday. I began to search the internet and to my surprise Amazon had the part and was able to deliver by Sunday. For less than the cost of a HVAC repair service call and 2 days sooner we had the part and a working furnace. The kit was very complete and the included instructions were great. Up and running in under 15 minutes.
Brent
February 8, 2025
Fit perfectly. Easy Dyi to save hundreds of dollars. Runs quietly.
Recommended Products
$280.05
$ 99 .00 $99.00