Your cart is empty.
Your cart is empty.Product Description
Paul
2025-07-28 13:22:20
The media could not be loaded.
Richard W
2025-07-27 12:29:47
I already have the 5†x 10†Geekpure whole house water filter housings and they work great. Easy to change out and no problems.Therefore I went with this 2.5†x10†housing for hooking up with my water dispenser unit next to the kitchen sink. This is a “ freebie “ from the builder but it requires proprietary filters that are very expensive. Instead I used the same 1/4†lines to hook up this unit. I used Sharkbite 1/4†to 1/4†couplings to lengthen the supply and feed lines so that instead of having the unit way in back and difficult to change the filters, I have it moveable so it is easily accessible for changing the filters or O ring if needed. This way I place the unit in a smaller bucket so any water that spills isn’t a problem. This also means I did not use the mounting bracket for the unit either but could have. If you just mount it so that you can slide it off easily than there is no stress on the bracket when torquing the body to loosen or tighten the body when changing the filter.Just be careful because most sink cabinets do not have very thick walls and if you use an anchor you might go through to either the dishwasher or into an adjoining cabinet. Another reason I find not mounting it works well.I have posted a question to Geekpure asking which manufacturer is best for replacement O rings for their product. Might help someone else out too.I always use Vaseline on O rings.
papin
2025-07-26 14:12:08
ok
Zurich
2025-06-14 16:36:43
Unfortunately, another example of poor quality Chinese crap. Housing uses brass threaded inserted but the bond between the insert and housing leaks on both inlet and outlet similar to what was described in other reviews. I installed it twice to verify that the theads sealed - they did. the leak was due to poor manufacturing quality control. It also comes with a very flimsy plastic mounting bracket the is unsuitable for any installation where unit isn't supported by the pipes (ie, flexible lines like PEX). Thankfully Amazon's return policy let me send this back.
Customer
2025-06-10 14:03:20
This whole house filter is excellent, very well made. I use it to filter my waste motor oil and it has held up very well.
Dan
2025-05-19 15:47:40
Everything it’s to be
Scott
2025-05-17 14:52:23
Added this filter housing to my fish room filter setup to use with a phosphate removal cartridge. Works great, does not leak.
Dan944
2025-05-14 11:14:22
Hard to stop from leaking
T. Mombourquette
2025-05-10 13:06:09
Whole house filter use
DiegoM
2025-04-14 12:30:14
Anche se non è trasparente lo consiglio poichè robusto ed è molto improbabile cge possa scoppiare come già successo con la versione trasparente.
PAIN philippe
2025-03-19 11:20:56
tres bien en pp tres resistant et bien alimentaire simple et bien etanche pas debage de serage on sere le corp de filtre parfais
watwessnicke
2025-03-14 13:50:20
Am Filtergehäuse gibt es im Grunde nichts zu meckern. Gut dass die Filtertasse undurchsichtig ist, da der Filter Aussenbereich installiert ist.Allerdings habe ich mich über die 3/4"-Innengewinde gewundert. Mit den sonst so bewährten 10 Lagen Teflonband kann man die Anschlüsse ganz locker von Hand bis zum Anschlag eindrehen. Ohne Werkzeug. Die Dichtigkeitsprobe habe ich mir da gleich geschenkt. Auch mit 17 (!) Lagen Teflonband war das Ganze viel zu locker. Ich habe es mit für mein Gefühl und meiner Erfahrung übertrieben viel Hanf und Paste eingedichtet. Das wird dann halbwegs fest. Also entweder meine Anschlusstücke, die vorher gewohnt stramm in 3/4"-Innengewinden saßen, sind bei der Demontage irgendwie geschrumpft, oder - was näher liegt - das 3/4"-IG des Filters ist zu groß. Ich bin ausgebildeter Installateur. Solche Mengen Hanf und Teflonband auf der Legende nach metallisch dichtenden Gewindeverbindungen sind mir fremd. Schönen Gruß von Herrn Witworth: "Das geht besser. Andere kriegen das auch hin.". Man bekommt es dicht, aber die Gewindeverbindungen sind nicht vertrauenerweckend. Ich habe ein Gartensprengventil am Filter. Mal schauen, was passiert, wenn ich seitlich am Schlauch ziehe...
Martin
2025-02-15 16:54:36
My old filter housing cracked at the 3/4 bsp port due to the plastic threads (no brass threaded insert) while changing the filter. This unit appears to be more solid in design and a straight forward replacment from my old unit even down to using the old mounting bracket made out of metal. Not sure how long the plastic mounting bracket with the new housing would have lasted. Its been up and running some months with no leaks happy person.
Recommended Products